China 3D Prints Airplane Structures Over 5 Meters Long

3D printing China

China is developing 3D printing for large structures for its combat aircraft. Strength, titanium, weight savings: the stakes of this technology.

In Brief

On November 14, 2026, the Aviation Industry Corporation of China (AVIC) announced a breakthrough in metal 3D printing applied to military aviation. Notably, the Shenyang Aircraft Design and Research Institute, responsible for developing the J-35 stealth fighters, manufactured a load-bearing structure over 5 meters long intended for an aircraft fuselage.

Chinese researchers also developed a multifunctional heat exchanger integrating multiple functions into a single part.

This technology, known as additive manufacturing, makes it possible to produce complex structures, reduce the number of assemblies, and optimize material usage.

Airbus, Boeing, Safran, and GE Aerospace already exploit these processes on commercial aircraft. Some printed parts are up to 45% lighter than their conventional equivalents.

The challenge remains guaranteeing their mechanical strength, particularly against fatigue. AVIC has not confirmed whether its new structures already equip operational J-35s.

China Announces a 3D-Printed Aeronautical Structure Over Five Meters Long

On November 14, 2026, AVIC presented several results achieved by the Key Laboratory of Aviation Science and Technology for Novel Aircraft Structures, integrated into the Shenyang Aircraft Design and Research Institute.

This institute notably participates in the development of the J-11, J-15, and the family of J-35 stealth fighters.

Its main achievement involves a metallic load-bearing structure of more than 5 meters (16.4 feet) intended for the central section of an aircraft fuselage.

Such a part must transmit mechanical stresses between different parts of the airframe. In particular, it withstands aerodynamic loads and stresses resulting from maneuvers.

According to AVIC, researchers developed a method combining the printing of multiple segments and assembly via additive fusion.

This approach bypasses the dimensional limitations of machines and reduces thermal deformations during manufacturing.

The laboratory also indicates that it has used six 3D printing processes, thirteen metallic materials, and nineteen categories of structures across various aerospace programs.

These results do not mean that a complete J-35 fuselage is now 3D-printed. The manufacturer did not specify which models will receive these new parts.

Additive Manufacturing Builds Metal Layer by Layer

Metallic 3D printing works in reverse to traditional machining.

In conventional manufacturing, a machine removes material from a metal block to obtain the desired geometry.

Additive manufacturing consists of depositing or fusing only the necessary material, following a three-dimensional digital model.

Lasers and Metal Powder Produce Complex Geometries

With Laser Powder Bed Fusion (LPBF) technology, a thin layer of metal powder is spread across a build plate. A laser selectively melts the areas corresponding to the part.

The plate then lowers, a new layer of powder is deposited, and the operation repeats.

Layer thicknesses are generally a few tens of micrometers.

Other processes use metal wire melted by a laser, electron beam, or electric arc. These are particularly suitable for large components.

Engineers can manufacture hollow parts, internal channel networks, or cellular structures that are practically impossible to machine conventionally.

The Chinese Process Combines Multiple Printed Parts

Shenyang developed a segmented manufacturing method to limit cracks and deformations caused by temperature variations.

The segments are produced separately, then joined by adding molten metal.

The institute also presented an annular heat exchanger intended for an aircraft air intake.

This part integrates four functions: heat transfer, air bleed, mechanical support, and maintenance accessibility.

To polish its internal channels, researchers use fine metal needles moved by a magnetic field.

The objective is to improve heat exchange and surface quality without having to open the part.

3D printing China

Printed Titanium Exhibits Strength Comparable to Conventional Alloys

The primary question concerns the strength of the printed metal.

Aviation notably uses the Ti-6Al-4V alloy, composed of approximately 90% titanium, 6% aluminum, and 4% vanadium.

Its density reaches 4.43 g/cm³, compared to about 7.8 g/cm³ for common steel.

Its tensile strength generally ranges between 900 and 1,100 MPa, depending on its metallurgical state and manufacturing process.

German manufacturer EOS notably announces a strength of 1,055 MPa for its Ti64 alloy printed under specified conditions.

A printed part can therefore achieve static strength comparable to that of a qualified conventional part.

However, this does not guarantee an identical lifespan.

Fusion defects, microporosities, and layer orientation can facilitate the appearance of cracks under repeated loads.

This phenomenon is called mechanical fatigue. It represents a major risk on combat aircraft subjected to significant accelerations and thousands of loading cycles.

Manufacturers use heat treatments, notably hot isostatic pressing (HIP), to reduce internal defects.

X-ray tomography, mechanical testing, and non-destructive testing complete the qualification.

A printed part is therefore neither intrinsically stronger nor necessarily more fragile. Its performance depends on the material, the process, and the inspections performed.

Western Industrialists Already Use 3D Printing on Their Aircraft

China is not discovering this technology. Several industrialists have already integrated it into their production.

The Airbus Group Prints Structural Titanium Parts

Airbus uses printed components on its A350s.

A door locking pin, once made of ten elements, is now produced as a single titanium piece.

According to Airbus, this new design is 45% lighter than the previous one.

The savings exceed four kilograms per aircraft when all sixteen concerned pins are replaced.

The manufacturer has also installed printed titanium structural brackets in the engine pylons of the A350.

GE Aerospace Manufactures Fuel Nozzles

GE Aerospace industrialized 3D-printed fuel nozzles for the LEAP engines powering the Airbus A320neo and Boeing 737 MAX, among others.

A new design replaces twenty assembled components with a single part.

According to GE, the nozzle is 25% lighter and five times more durable than its predecessor.

The company had already manufactured 30,000 nozzles via 3D printing by 2018.

Boeing and Safran Produce Certified Components

Boeing has been using structural titanium parts manufactured by Norsk Titanium for its 787 Dreamliner since 2017.

Safran obtained EASA and FAA certifications in 2019 for a LEAP engine lubrication center housing produced by laser powder bed fusion of aluminum.

These achievements demonstrate that additive manufacturing is now a qualified industrial method rather than merely a prototyping technique.

Weight Savings and Production Efficiency Explain Aircraft Manufacturers’ Interest

The main advantage comes not only from the material used, but from the freedom offered to designers.

A structure can be reinforced precisely where it bears loads while eliminating unnecessary material.

This topological optimization often produces geometries close to biological structures, with internal ribs and cavities.

It also makes it possible to eliminate certain fasteners, welds, and assembly operations.

For a fighter jet, saving several tens of kilograms can help increase payload capacity, range, or performance margins.

Material yield constitutes another advantage. Airbus indicates that a conventional process can require up to ten times the final mass of a part in raw material, compared to about 1.5 times with certain additive techniques.

However, the benefits remain specific to each component. Additive manufacturing does not automatically guarantee lower costs, particularly when finishing and inspection operations are extensive.

Stealth Fighters Could Benefit From More Integrated Structures

For the J-35 as for the Chinese J-20 stealth fighter, weight reduction is only part of the appeal.

Integrating internal conduits, electronic supports, or cooling systems can simplify the aircraft’s architecture.

On a stealth fighter, reducing the number of assemblies and facilitating equipment integration also presents an industrial advantage.

This does not mean a printed part is automatically harder to detect by radar. Stealth always depends on external geometry, absorbing materials, and the control of electromagnetic signatures.

Shenyang’s work could also benefit future fighter jets and military drones, whose shapes and internal systems are becoming increasingly complex.

Fatigue Resistance Remains the Real Industrial Challenge

Shenyang’s success marks an important progression in manufacturing large metallic structures.

However, printing a five-meter part is not enough to prove that it can withstand several thousand hours of flight.

Engineers will need to validate its strength, assemblies, dimensional stability, and manufacturing repeatability.

The real shift will occur when large load-bearing structures can be regularly produced, inspected at an acceptable cost, and integrated into operational aircraft.

3D printing could then profoundly modify aeronautical construction. Aircraft manufacturers would no longer be forced to design their airframes solely around machining and assembly constraints.

China is precisely seeking to cross this step: moving from manufacturing small parts to producing large integrated aeronautical structures.